期刊名称：JOURNAL OF REINFORCED PLASTICS AND COMPOSITES
 期刊简介(About the journal)
投稿须知(Instructions to Authors)
编辑部信息(Editorial Board)
About the journal
|
The Journal of Reinforced Plastics and Composites presents research studies on a broad range of today's reinforced plastics and composites. Original peer-reviewed reports based on research, analysis, testing and industrial experience, examine advances in these areas:
¡¤ Constituent materials: matrix materials, reinforcements and coatings.
¡¤ Properties and performance: The results of testing, predictive models, and in-service evaluation of a wide range of materials are published, providing the reader with extensive properties data for reference.
¡¤ Analysis and design: Frequency reports on these subjects inform the reader of analytical techniques, design processes and the many design options available in materials composition.
¡¤ Processing and fabrication: There is increased interest among materials engineers in cost-effective processing.
¡¤ Applications: Reports on new materials R&D are often related to the service requirements of specific application areas, such as automotive, marine, construction and aviation.
Reports on special topics are regularly included such as recycling, environmental effects, novel materials, computer-aided design, predictive modelling, and "smart" composite materials.
|
 |
Instructions to Authors
The primary purpose of the Journal of Reinforced Plastics and Composites is to provide a permanent record of achievements in the science, technology, and economics of reinforced plastics and composites. Implicit in this objective is the recognition and appropriate publication of the accomplishments of all participating interests.
Fulfillment of this purpose depends almost entirely upon the voluntary contribution of articulate, accurate, and authoritative manuscripts. In addition to the multiple reviewing of candidate manuscripts to assure high standards of technical veracity, editorial selectivity also involves consideration of the equitable coverage of the entire field.
In further discharging its responsibilities, the journal endorses the content and programs of appropriate trade associations and professional societies, but asserts its independent role in both the recording and, if necessary, appraising of their activities.
INSTRUCTIONS FOR AUTHORS
Submitting Papers to the Journal:
1. Electronic submission of the manuscript as a PDF or MS Word file attached to an email message sent to gspringer@stanford.edu is the desired format for submission of papers. Otherwise, five double-spaced hard copies and one electronic version (on a 3.5 in. disk or CD using Microsoft Word in an IBM/PC format) should be submitted to:
Editor, George S. Springer,
Journal of Reinforced Plastics and Composites,
Dept. of Aeronautics and Astronautics,
Stanford University,
Stanford,
CA 94305, USA.
Revised manuscripts should be resubmitted in final print and electronic versions.
2. Centred title should be brief, followed by centred name, affiliation, address, country, and postal code (zip) of author(s). Indicate to whom correspondence and proofs should be sent, including a telephone number, fax number and e-mail address.
3. Include a 100-word abstract.
4. Include a list of key words.
5. A list of five potential reviewers should be submitted to the Editor at the time of manuscript submission [optional].
6. ILLUSTRATIONS
-Computer generated graphics. Any art that is sent electronically should be in .tif files, in 300 dpi resolution, for superior reproduction. Colour original should be saved as greyscale images.
-Line Drawings. Originals should always be submitted. Wherever possible, graphs should be boxed in, and scale divisions should be marked on the inside of the boxes. Grids should not be shown. Insofar as possible, explanations should be placed in the legend. Original drawings should not be larger than 20x25 cm (8x10 in); if this is impossible, they must be accompanied by two sets of small photoprints. Measurements should be indicated in SI units.
-Lettering should be planned for 50% reduction; text must be readable after reduction.
-Photographs. Photographs should be supplied as glossy prints, and wherever possible, of the same size as they are to appear in the journal. Illustrations should be referred to as Figure 1, Figure 2, etc. The name(s) of the author(s) should be written on all illustrations, as should the Figure number. The indication 'Top' must be given, if necessary. Besides the original illustrations, one duplicate set must accompany each copy of the manuscript; these copies may be photoprints, if clear and legible.
-Text must be readable after reduction.
7. JOURNAL AND BOOK REFERENCES should be identified in the text using the Vancouver system [numbered notes throughout text, numbered list at end of article].
Literature references should be listed by number at the end of manuscript as reference number, Author(s), date, 'title of article,' title of publication, volume, page, publisher, place of publication, etc. Examples:
1. Name 1, A.A. and Name 2, B.B. (year of publication). A Method of Damage Detection for Rotating Systems, Journal Name, 107(3): 275-281.
2. Name, C.C. (year of publication). Title of Chapter, Book Name, Edition (if not first), page, publisher, place etc.
8. FIGURE, TABLE, EQUATION: spelled out in text, capitalized. Figure 1 Table 1 Equation (9)
9. TABLES. Number consecutively and type on a numbered, separate page.
Please use arabic numerals and supply a heading. Column headings should be explanatory and carry units (see example). Do not include vertical rules.
10. UNITS & ABBREVIATIONS. SI units should be used.
11. SYMBOLS. A list of symbols used and their meanings should be included if a
large number of symbols appears in the text.
12. PROOFREADING AND OFFPRINTS. Authors will receive page proofs, which
they should correct and return as soon as possible. An offprint order form for purchase of additional offprints will be provided. No free offprints can be provided; the correspondence author will receive one free copy of the journal for each contributor.
13. COPYRIGHT INFORMATION. All original journal articles are copyrighted in
the name of the publisher. All original articles accepted for publication must be accompanied by a signed copyright transfer agreement available from the journal editor or from the publisher's website. Previously copyrighted material may be published with the written permission of the copyright holder.
14. HEADINGS. Your article should be structured into sections. Normally two headings are used as follows:
Main Subhead: DESIGN OF A MICROWAVE INSTALLATION [all capital letters, centred]
Secondary Subhead: Principle of the Design Method [capitalize first letter of main words, left justified]
15. EQUATIONS. Number equations with arabic numbers enclosed in parentheses at the right-hand margin. Type superscripts and subscripts clearly above or below
the baseline, or mark them with a caret. Be sure that all symbols, letters, and numbers are distinguishable (e.g., 0 for zero, one or lowercase 'el', 'vee' or Greek nu).
16. PERMISSIONS. The author is responsible for obtaining releases from other publishers for Sage Publications to publish material copyrighted by someone else.
GENERAL
Neither Journal of Reinforced Plastics and Composites nor the editorial board or Sage Publications is responsible for the views expressed by individual contributors in articles published in the Journal.
Editorial Board
|
|
|
|
| L. Kollar ,Department of Mechanics and Structures, Budapest University of Technology and Economics, 1521 Hungary, M¨¹egyetem rkpt.3 | |
| A.C. Loos ,Virginia Polytechnic Institute & State University, USA | |
|
|
|
|
|
|
| J.M. Whitney ,Air Force Materials Laboratory, Dayton, OH, USA | |
|
刊名字顺( Alphabetical List of Journals):
返回页首 