期刊名称：ADVANCED POWDER TECHNOLOGY
 期刊简介(About the journal)
投稿须知(Instructions to Authors)
编辑部信息(Editorial Board)
About the journal
The international journal of the Society of Powder Technology, Japan. Published jointly with the Society of Powder Technology, Japan.
The aim of Advanced Powder Technology is to meet the demand for an international journal integrating all aspects of research on powder engineering and technology. The journal fulfils this aim by publishing original research papers (including translations of papers originally published in Japanese), notes, review papers, letters to editor, book reviews, general articles and announcements. Although Advanced Powder Technology was founded as the International Journal of the Society of Powder Technology, Japan, researchers world-wide are invited to submit papers for publication in this journal.
Advanced Powder Technology reports on research in various areas of powder technology such as particle characterization, mechanical powder properties, storage, conveying, comminution, classification, agglomeration, mixing and kneading, dispersion, reactor design, dust, separation, filtration.
ISSN 0921-8831
E-ISSN 1568-5527
Instructions to Authors
Submission of an article is understood to imply that the article is original and unpublished and is not being considered for publication elsewhere. Reviews of specialized topics are also welcome, after the authors obtain preliminary approval from the Editor-in-Chief.
General
Typescripts should be typed in English, double spaced and single-sided on A4-sheets and should be numbered beginning with the title page. The first page of an article should contain the title of the paper, the name(s) and address(es) of all the author(s) and the author to whom correspondence and proofs should be addressed. An abstract of 50--200 words should follow the title page on a separate sheet.
Text
Headings and subheadings for different sections of the paper (e.g. Introduction, Methods, Results, Discussion, Conclusion) should be clearly indicated. Units of measurement, abbreviations and symbols should follow the International System of Units (Sl). Equations and formulae should be typewritten. Equations should be numbered consecutively with arabic numerals in parentheses on the right-hand side of the page.
Tables and figures
Tables should be given short informative titles and should be numbered consecutively in arabic numerals. Tables may be reproduced by photo-offset, i.e. directly from the typed manuscript. Figures in a form suitable for reproduction should be submitted separately from the text as original drawings, or as high contrast, sharp photographs on glossy paper. Lettering on figures should be proportional to the size of the figure to ensure legibility after reduction. On the back of each figure the author and figure number should be indicated. All figures and tables should be cited consecutively in the text and a list of descriptive captions should be provided at the end of the paper.
References
References should be cited in the text using a number in square brackets in order of appearance, and listed at the end of the paper in numerical order.
List of references
For a periodical
1. E. Otto and H. Fissan, Brownian coagulation of submicron particles, Adv. Powder Technol., 10, 1--20 (1999).
For a book
2. S. K. Friedlander, Smoke, Dust and Haze, pp. 119--142. Wiley, New York (1977).
For an article in a book
3. C. S. Campbell and A.V. Potapov, Computer simulation of particle breakage, in: Powder Technology Handbook, 2nd Edition, K. Gotoh, H. Masuda and K. Higashitani (Eds), pp. 795--809. Marcel Dekker, New York (1997).
For a paper in a conference proceedings
4. H. Takase, K. Higashi and M. Sugimoto, Effect of coal slurry properties on deashing by oil agglomeration, in: Proc. 2nd World Congress Particle Technol., IV, pp. 556--563. Kyoto (1990).
If a publication is in press, the reference should be made as complete as possible, stating the name of the journal and adding `in press'.
Proofs
Proofs will be sent to the designated author to check typesetting accuracy. No changes of the original manuscript are accepted at this stage. Proofs should be returned within two days of receipt.
Reprints
Reprints may be ordered at prices shown on the reprint order form, which will be sent to the author together with the proofs.
Editorial Board
Editor-in-Chief:
K. Higashitani
The Society of Powder Technology, Japan
7F, No. 5 Kyoto Bldg.
181 Kitamachi,
Karasuma-dori
Rokujo-agaru, Shimogyo-ku,
Kyoto 600-8176
Japan
Tel: +81-(0)75-351-2318
Fax: +81-(0)75-352-8530
aptj@nifty.com
Editorial Board:
Y. Endo Sumitomo Chem. Co. Ltd., M. Fuji Nagoya Inst. of Techn., K. Gotoh Yamaguchi Univ., I. Irtani Nagoya Univ., H. Kamiya Tokyo Univ. of Agr. & Techn., Y. Kanda Kyoto Univ., H. Makino CRIEPI, H. Mori University of Nagoya, M. Naito Osaka Univ., K. Okuyama Hiroshima University, A. Shimosaka Doshisha Univ., H. Suzuki Shizuoka University, T. Tanaka Osaka University, T. Tanino Shionogi & Co. Ltd., S. Watano Univ. of Osaka Pref., J. Yoshida Shimizu Corporation
Advisory Board:
C.S. Campbell Los Angeles, CA, USA, C.E. Capes Ottawa, Canada, R. Davies Gainesville, USA, L.T. Fan Manhattan, KS, USA, M. Ghadiri Leeds, UK, K. Gotoh Toyohashi, Japan, C. Kanaoka Kanazawa, Japan, S.H. Kang Gyongsan, Korea, Y. Kawashima Gifu, Japan, Y. Kousaka Sakai, Japan, H. Leuenberger Basel, Switzerland, J. Li Beijing, PRC, R. Pfeffer Newark, NJ, USA, S. Pratsinis Zurich, Switzerland, P. Ramakrishnan Bombay, India, A.W. Roberts Newcastle, Australia, B. Scarlett Gainesville, USA, M. Senna Yokohama, Japan, K. Shinohara Sapporo, Japan, H. Yamamoto Tokyo, Japan, S. Yuu Kitakyusyu, Japan, R.A. Williams Leeds, UK
Typescripts should be submitted in triplicate to the Editor-in-Chief:
7F, No. 5 Kyoto Bldg.
181 Kitamachi,
Karasuma-dori
Rokujo-agaru, Shimogyo-ku,
Kyoto 600-8176
Japan
Tel: +81-(0)75-351-2318
Fax: +81-(0)75-352-8530
E-mail: aptj@nifty.com
|
